Welcome to RoadBuck Kenya
Welcome to RoadBuck Kenya
83 results
Retractable cable reel for safe power distribution around the bay.
Compact chassis straightening bench for smaller bodyshops.
Enclosed spray and bake booth with diesel-fired heating.
NewEnclosed spray booth with electric heating for paint application and curing.
Infrared curing lamps for accelerating paint and filler drying.
High-pressure washer for continuous commercial wash duty.
Snow foam applicator for pre-wash and vehicle detailing.
Steam cleaner for interiors, engine bays and detailing, on standard supply.
Higher-output steam cleaner for continuous commercial use.
Manual grease dispensing unit for chassis and bearing lubrication.
Wet and dry workshop vacuum with a 70 litre drum.
Very high capacity jack for heavy plant and industrial lifting.
Portable jacking lift for raising a vehicle without a fixed installation.
Axle stands for safely supporting a vehicle once jacked.
Hydraulic shop press for bearings, bushes and pressed fittings.
Manual coil spring compressor for strut and suspension work.
Hydraulic coil spring compressor for faster, safer strut work.
Brake disc resurfacing lathe for routine brake service.
Brake lathe handling both discs and drums on one machine.
NewAutomatic air conditioning recovery, vacuum and recharge station.
Workshop battery charger for routine charging and conditioning.
Portable jump starter and charger for flat batteries.
Rolling tool cabinet supplied with a 258-piece tool set.
Rolling tool cabinet supplied with a 306-piece tool set.
Compact piston compressor for a single bay or mobile use.
Piston compressor for a small workshop running one or two air tools.
Mid-size piston compressor for steady multi-tool demand.
300 litre piston compressor for a multi-bay workshop.
300 litre high-pressure compressor for applications needing 15 bar.
500 litre compressor for continuous demand across several bays.
New500 litre high-pressure compressor for heavy or industrial air demand.
Heavy-duty pneumatic impact wrench for truck and bus wheel work.
Standard pneumatic impact wrench for passenger car wheel work.
Mid-size pneumatic impact wrench for light commercial vehicles.
Low-speed air drill for controlled drilling and reaming work.
Air-driven sander and grinder for panel preparation and finishing.
Vacuum pump for air conditioning service and system evacuation.
Workshop welding plant for bodywork, fabrication and repair.
Spot dent puller and sheet metal repair station for panel work.
Full-size chassis straightening bench for structural collision repair.
Two-post lift with a floor base plate, for bays where an overhead beam is not practical.
Drive-on four-post lift suited to alignment work, servicing and vehicle storage.
Space-saving single-column lift for workshops with a tight footprint.
Scissor lift with alignment platforms and rear slip plates, built for a dedicated alignment bay.
Full-size scissor lift for heavier vehicles and longer wheelbases.
Recessed full-size scissor lift that sits flush with the floor when lowered.
Compact surface-mounted scissor lift with a 1.2 metre platform.
Surface-mounted scissor lift with a longer 1.8 metre platform.
Recessed compact scissor lift, flush to the floor to keep the bay clear when not in use.
Pit-mounted rack for under-vehicle access without a full lift installation.
Pit rack supplied with support legs for freestanding installation.
Swing-arm tyre changer for passenger car and light van wheels.
NewUprated GT325 with assist tooling for stiffer sidewalls and low-profile tyres.
Heavy-duty changer for truck, bus and light commercial wheels.
Spreader for inspecting and repairing truck tyre casings from the inside.
Mid-range computerised aligner for a busy alignment bay.
NewTop-of-range computerised aligner for high-throughput tyre and alignment centres.
Digital wheel balancer for car and light van wheels, available in standard and P variants.
NewHigher-specification digital balancer with faster cycle handling, in standard and P variants.
Replacement and spare wheel clamps for alignment target mounting.
Bench grinder for preparing tyre casings ahead of patch repair.
Heated press for permanent vulcanised tyre and tube repairs.
Front-wheel turntable plates used during alignment measurement.
Multi-brand diagnostic scanner for fault reading and live data.
NewAdvanced diagnostic platform with wider vehicle coverage and bi-directional testing.
New
General-purpose hand tool set for a working service bay.
Rolling tool cabinet supplied with a 253-piece tool set.
Symmetric two-post hydraulic lift for general garage servicing.
What you see here is what we currently display, not the limit of what we supply. Tell us the machine, the make or just the job it has to do, and we’ll source it and come back with a quotation.